Vehicles
23 not categorized PORSCHE 997 TURBO CARRERA IICan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD34310020L FVD-alu-camberplates replace soft top strut rubber bushings. The FVD-camberplates are machined from billeted aluminum, providing you with a wide range of camber possibilities. You can get up to 4 degrees negative camber. FVD-alu-camberplates fits on original-shocks and cup-shocks. General Fitment911 1970-73
$434.27
Make a selection FVD34710001
General Fitment911 1970-73
$475.77
Make a selection FVD34791100 Lowering your car without a bump steer kit effectively pulls the steering out of alignment and requires constant steering adjustments that make the car difficult to control. This adjustable bump steer kit will fully compensate to return the steering rack / geometry back to pre-lowered specifications. Our bump steer kit is manufactured to the highest of German standards to ensure the quality, performance and reliability you expect from your Porsche. Features: alloy steel, sealed spherical rod end 14 mm tapered wedge for secure fitment inside the steering arm made for lowering below 30 mm (1.18 inches) / raised spindles allows tie rods to be adjusted downwards no binding throughout suspension travel range finishe...(choose a part on the right to read more) General Fitment911 1970-73
From $284.90
Make a selection FVD35103ABE The zimmermann sport brake disc combines high-quality cast materials, a vented and drilled braking surface and includes z-coating. This is a direct replacement for original number 477 405 083 d. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty drilled look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Sold individually. 2 rotors would be needed for the front axle. Left or right side fitment. General Fitment944 1982-85944 1985-88 924 1980-85 914 1970-76 911 1970-73
From $149.24
Make a selection FVD35215 Sporting lookbetter coolingremoves wetness and contamination fast General Fitment944 1982-85944 1985-88 928 1992-95 924 1980-85
From $182.79
Make a selection FVD37504300R
General Fitment911 1970-73
$64.90
Make a selection FVD503930001 Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) complete front fender set that includes headlight buckets and rear exit vents. Gas filler is not included with these fenders. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight left and right side. - made of high strength, grp (glass-reinforced plastic) sold as a set. 1 necessary per car. Please note: this only fits in conjunction with widebody / rsr rear bumper, part # 10050305503gfk and rear fenders, part # FVD503930003 . Please provide us with the year / model. These are high quality parts that take time to manufacture and cure properly. Lead tim...(choose a part on the right to read more) General Fitment911 1970-73
From $2,006.40
Make a selection FVD50399701MM Louvers slats they are such a unique feature, so important. By opening the front fenders, and allowing the hot air from the brakes to get ventilated out of the wheel arch! To mount on top or bottom of the exist front fender. For all Porsche 997 Carrera | s | 4s | GTS | GT3 | targa | turbo s | GT2 | GT2 rs | sport classic
$640.20
Make a selection FVD55522002GFK4 Glass fiber komposite (gfk) / glass reinforced plastic (grp), German made race dashboard. Saves 4 kg (8.8 lbs.) needs to be trimmed, sanded, primed and painted. Sold individually. 1 necessary per car. Please note: please supply your FVD part specialist with the year and model of your car. These are made to order. General Fitment911 1970-73
From $662.38
Make a selection FVD55522002GFK3 Ist nur für rennfahrzeuge, dient der gewichtsersparnis von ca. 4kg, hat keine 100% passgenauigkeit, anpassungsarbeiten eventuell erforderlich. General Fitment911 1970-73
$828.30
Make a selection FVD512911001 Festigkeitsgutachten liegt vor General Fitment911 1970-73
$3,016.64
Make a selection FVD55091196401 Kit contains: 6x intake-, 6x exhaust valve, 12 x retainers titan, 24 x valve stems, valve springs. General Fitment911 1989-94914 1970-76 911 1970-73
From $2,718.50
Make a selection FVD50599704MM Side skirts set tradition rs our side skirts are much wider than the stock components, which leads to a wider underbody and thus to more downforce. The mounting is very easy. Plug&play at the OEM screwing points. For all Porsche 997 Carrera with the (c4) wide body | 4 | 4s | GT2 rs | GT3 rs | turbo
$1,075.80
Make a selection FVD51299701MM Rear diffuser for all Porsche 997.1 Carrera models. The mounting is very easy. Plug & play with 3M double tape and 2 screws on the screwing points. Not for models with the turbo | GT2 | GT3 rear bumper
$1,312.30
Make a selection FVD98010001 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 478kw (650hp) @ 8000rpm max. Torque - 640nm @ 6000rpm max. Speed - 340km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.8s our Carrera GT ecu programming offers you not only more power and torque but phenomenal sound! Within the cgt end muffler is a flap-type mechanism fitted which is controlled by vacuum units. These vacuum units are also controlled by the ecu. Our programming modifies the control of these f...(choose a part on the right to read more)
$7,594.36
Make a selection FVD58098100 High-quality stainless steel roll-over system with installation kit. General Fitment911 2005-08911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$2,999.56
Make a selection FVD98010002 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter 1 x sport exhaust system genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 496kw (675hp) @ 8000rpm max. Torque - 670nm (495 lbf ft) @ 6000rpm max. Speed - 345km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.7s FVD dme / ecu programming philosophy: for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. ...(choose a part on the right to read more)
$17,032.10
Make a selection FVDR3035101 Brake system front with big red calippers General Fitment914 1970-76911 1970-73
From $3,177.64
Make a selection FVD50599702MM Front bumper air vent grill an important component for both cooling and aerodynamics. Ensuring the rapid removal of hot air optimized unit cooling front bumper rs grill for all Porsche 997 Carrera models incl. 4s / GTS / GT3 / turbo
$366.30
Make a selection FVD35203Z The zimmermann sport brake disc combines high-quality cast materials, a vented and drilled braking surface and includes z-coating. This is a direct replacement for original number 901 352 041 14. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty drilled look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Sold individually. 2 rotors would be needed for the rear axle. Left or right side fitment. General Fitment911 1970-73
From $141.90
Make a selection HEI911001001S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: weld-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness bar, part...(choose a part on the right to read more) General Fitment911 1970-73
From $602.01
Make a selection HEI911001002S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: weld-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness bar, part...(choose a part on the right to read more) General Fitment911 1970-73
From $602.01
Make a selection HEI911001006S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Semi-gloss black finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold ala carte. Please note: th...(choose a part on the right to read more) General Fitment911 1970-73
From $1,502.00
Make a selection HEI911001005A Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Aluminum finish. Primarily for street use as a harness bar is not an option. Please note: these bars are hand made to order. They typically take between...(choose a part on the right to read more) General Fitment911 1970-73
From $1,661.93
Make a selection HEI911001007S Optional : General Fitment911 1970-73
$1,473.97
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |